Need Bios settings i7 930 p6x58d Premium ddr3-2000

[mitchell]

CPU: i7 930
Motherboard: p6x58d Premium
gSkill Memory: f3-1600CL9T-6GBRH (DDR3-2000)
Windows 7 x64

I had it running at 2000 But would get BSOD When running AVS Video Converter. if I go back to everything auto its fine

I have 3 Questions With #1 the most important at the moment Since I have only a stock fan.
1.) What would be the Settings for my configuration to run the memory at 2000Mhz with stock CPU Fan. No Memory Fans
2.) What is a good Fan for the CPU and Memory if I would want to Over Clock
3.) What are the Bios setting I would need for my Configuration with the better CPU fan Kit and Memory Fan Kit already installed.
Thanks Mitch

[Tradesman]

Gskill might have these types of settings handy, I'll have to check into it - will try and get something on Sun

[mitchell]

Support
Anyone?

[GSKILL TECH]

1) DDR3-1600, 7-7-7-24, 1.60V. Input that in BIOS and you should be ready to go.

2) CPU fan, Thermalright Ultra 120, True Black, Silver Arrow / Prolimatech Megahalem

Memory fan, the G.Skill Turbulence II

3) Enable XMP, then find the precise QPI/DRAM Core Voltage needed to stabilize DDR3-2000

Thank you
GSKILL TECH

[mitchell]

thank you I will give these a shot

[mitchell]

I tried
1) DDR3-1600, 7-7-7-24, 1.60V. Input that in BIOS and you should be ready to go.
Ran prime95 for 64bit and it blue screened with in 1 minute.
then increased the voltage to 1.6250
It blue screened again after 2 minutes Should I keep trying to increase the voltage?
here is my Settings can you look it over and suggest anything?

Could I overclock a little with stock fan or just rum ddr3-2000 with correct settings?

[HTML]****************************
AI Tweaker
****************************

Ai Overclock Tuner........... = [AUTO]
CPU Ratio Setting............ = [AUTO]
Xtreme Phase Full Power Mode. = [Enabled]
DRAM Frequency............... = [DDR3 - 1600MHz]
UCLK Frequency............... = [AUTO]
QPI Link Data Rate........... = [AUTO]
ASUS/3rd Party UI Priority....= [ASUS Utility]

CPU Voltage Control.......... = [Manual]
CPU Voltage.................. = [AUTO]
CPU PLL Voltage.............. = [AUTO]
QPI/DRAM Core Voltage........ = [1.6250]
IOH Voltage.................. = [AUTO]
IOH PCIE Voltage............. = [AUTO]
ICH Voltage.................. = [AUTO]
ICH PCIE Voltage............. = [AUTO]
DRAM Bus Voltage............. = [AUTO]
DRAM DATA REF Voltage on CHA. = [AUTO]
DRAM CTRL REF Voltage on CHA. = [AUTO]
DRAM DATA REF Voltage on CHB. = [AUTO]
DRAM CTRL REF Voltage on CHB. = [AUTO]
DRAM DATA REF Voltage on CHC. = [AUTO]
DRAM CTRL REF Voltage on CHC. = [AUTO]

Load-Line Calibration........ = [AUTO]
CPU Differential Amplitude... = [AUTO]
CPU Clock Skew............... = [AUTO]
CPU Spread Spectrum.......... = [AUTO]
IOH Clock Skew............... = [AUTO]
PCIE Spread Spectrum......... = [AUTO]

*******************
DRAM Timing Control
*******************

1st Information: 7-7-7-24-5-88-12-8-24-0
DRAM CAS# Latency............ = [7 DRAM]
DRAM RAS# to CAS# Delay...... = [7 DRAM]
DRAM RAS# PRE Time........... = [7 DRAM]
DRAM RAS# ACT Time........... = [24 DRAM]
DRAM RAS# to RAS# Delay...... = [AUTO]
DRAM REF Cycle Time.......... = [AUTO]
DRAM WRITE Recovery Time..... = [AUTO]
DRAM READ to PRE Time........ = [AUTO]
DRAM FOUR ACT WIN Time....... = [AUTO]
DRAM Back-To-Back CAS# Delay. = [AUTO]

2nd Information: 1N-58-58-59
DRAM Timing Mode............. = [3N]
DRAM Round Trip Latency on CHA = [AUTO]
DRAM Round Trip Latency on CHB = [AUTO]
DRAM Round Trip Latency on CHC = [AUTO]

3rd Information: 8-8-18-8-8-8-7-6-4-7-7-4
DRAM WRITE To READ Delay (DD) = [AUTO]
DRAM WRITE To READ Delay (DR) = [AUTO]
DRAM WRITE To READ Delay (SR) = [AUTO]
DRAM READ To WRITE Delay (DD) = [AUTO]
DRAM READ To WRITE Delay (DR) = [AUTO]
DRAM READ To WRITE Delay (SR) = [AUTO]
DRAM READ To READ Delay (DD) = [AUTO]
DRAM READ To READ Delay (DR) = [AUTO]
DRAM READ To READ Delay (SR) = [AUTO]
DRAM WRITE to WRITE Delay (DD)= [AUTO]
DRAM WRITE to WRITE Delay (DR)= [AUTO]
DRAM WRITE to WRITE Delay (SR)= [AUTO][/HTML]

[GSKILL TECH]

STOOOOOOPPPPP you're going to FRY the CPUUUUUU!!!

NooOOOoOooOoOOOOOOooOoOooo haha

QPI/DRAM Core Voltage......should be AUTO.

DRAM Bus Voltage............. = [1.60V]

Also, DRAM Timing Mode............. = [1N or 2N]

Thank you
GSKILL TECH

[mitchell]

OK I corrected that to:
QPI/DRAM Core Voltage......should be AUTO.
DRAM Bus Voltage............. = [1.60V]
Also, DRAM Timing Mode............. = [1N or 2N] used 1N

loaded prime95 it ran then had an error and stopped (unloaded) I loaded it again then BSOD rebooted and hear I'm

[GSKILL TECH]

Try 2N, then one module at a time to make sure all modules are error free.

Do you have the latest BIOS? Those settings should work flawlessly..

Post the 1st Information numbers so I can check advanced timings.

Thank you
GSKILL TECH

[mitchell]

I have the latest bios got it yesterday

1st info is
1st Information: 7-7-7-24-5-88-12-8-24-0

I ran prime 95 again lasted 3 minutes then it stopped with application stopped windows is finding a solution then a close application and here I'm

Going to test each stick now

[mitchell]

Ran 1 Pass on each stick with memtest+ Boot-able CD
all Passed
then put all sticks in 3 of them and did another test got this 2 errors


then I rebooted and got a overclocking failed error

[GSKILL TECH]

Try DRAM Voltage 1.65V

Thank you
GSKILL TECH

[mitchell]

1.65 gave me a warning. put it on 1.64v and did 1 1/2 passes


Took this if it helps lowered back down to 1.60v's by the way after above test

[GSKILL TECH]

Try higher timings like 8-8-8-24. If the same problem persists, the modules may be slightly defective. I can't see why else they are not working properly.

Thank you
GSKILL TECH

[mitchell]

That did it got 2 passes and no errors with 1.60 volts and 8-8-8-24

Does that mean I'm good to go and how does it effect me from running 2000mhz?

What would I have to do to achieve 2000?